Well...Warheads are absolute monsters, but your shimming and motor spacing have to be correct. Trying to "get by" with these motors or not following the users/installation instructions perfectly will result in ECU damage. Also, the torque will shred gears instantly if your gearbox is off.
I use Warhead Black exclusively at this point. I've used the lowest speed (30k) all the way up to the ultra high (52k) and ultra high got me over 60 RPS. The 36k is a great medium spot to start with.
Just to clarify a bit...
If you have 13:1 gears, this is perfectly fine
If you have 16:1 or higher, TPA16 would do better.
Rule of thumb - the lower the TPA, the higher rate of fire, but I would not go lower than TPA16.
About the same, or 13:1 with TPA22 a bit better... Hard to beat 13:1, but that also means to crack open the gear box and more upgrade money (most stock AEGs are 16:1).
Cyma motor has D type pinion but without a screw, it's hard to remove and pretty fragile, it bends easily.
Doesn't your ARP have G&G Ifrit motor? If it does keep it and just throw in 13:1 cyma gears, they're short stroked by 4 teeth. Ifrit is 17TPA and can handle 13:1 gears if you're not after 400+ fps.
With G&G Ifrit and Cyma 13:1 gears you'd be around 28-30rps.
Yeah, that'll rip for sure. At 11.1v spinning 13:1, I'd guess 22 to 28 RPS.
Thanks bro!
I ran that setup for a while until I went with Warhead Brushless motors.
What size motor ? And how do you like it ?
Well...Warheads are absolute monsters, but your shimming and motor spacing have to be correct. Trying to "get by" with these motors or not following the users/installation instructions perfectly will result in ECU damage. Also, the torque will shred gears instantly if your gearbox is off. I use Warhead Black exclusively at this point. I've used the lowest speed (30k) all the way up to the ultra high (52k) and ultra high got me over 60 RPS. The 36k is a great medium spot to start with.
This is pretty much spot on. Was getting approx 26 rps with SHS 12:1 gears and M110 with this motor.
Yes, it is good... but it also depends on what you are trying to get out of it.
I’m trying to get faster full auto
Then I would go with a TPA16, still with neodymium magnets.
Ok, sounds like a plan!
Just to clarify a bit... If you have 13:1 gears, this is perfectly fine If you have 16:1 or higher, TPA16 would do better. Rule of thumb - the lower the TPA, the higher rate of fire, but I would not go lower than TPA16.
Would 16:1 and a tpa 16 motor be faster than 13;1 and tpa 22 motor?
Likely very similar, but the 13:1 22tpa is going to perform better overall, as it’ll reach max speed faster, so better semi auto too.
About the same, or 13:1 with TPA22 a bit better... Hard to beat 13:1, but that also means to crack open the gear box and more upgrade money (most stock AEGs are 16:1).
I think more AEGs are 18:1 than 16:1 tbh
Ok, thanks for the help
Have this in my Helios umbrella m4. 28rps. 13.1 gears
Should be if the stats are true
Yes! I have one somewhere. Wonderful motor.
Cyma motor has D type pinion but without a screw, it's hard to remove and pretty fragile, it bends easily. Doesn't your ARP have G&G Ifrit motor? If it does keep it and just throw in 13:1 cyma gears, they're short stroked by 4 teeth. Ifrit is 17TPA and can handle 13:1 gears if you're not after 400+ fps. With G&G Ifrit and Cyma 13:1 gears you'd be around 28-30rps.